First complete FF 91 body-in-white (BiW) for assembly starts build path at Faraday Future Hanford facility | Sheet Metal Roofing Screws

The best-known Karachi poster artists were: Wazir, who bought a lithographic machine from Azad, and is best-known for Begum Jaan; Kasim and A.H. Mahver (known for their more monochromatic palette) and banner painters who travelled between Karachi, Faisalabad and Multan, M.M., a favourite of Satish Anand, Pervez, Aslam and Jeewan who made banners for English films; Majid, Ghulam Rasool (Chota) Sarwar (better known as Arif Githa and Akhtar who was both an actor and an artist. There are only a few banner painters left in Karachi and in Lahore of whom Ajmal is the best-known. While some cinema artists such as Rafique, son of Mustafa Chughtai, went to an art school, most apprenticed at a young age. Ustad Allah Buksh was greatly respected by all and trained many a cinema painters.

In a span of four days, AdAsia delegates are expected to listen (attentively, if possible) to about 45 distinguished speakers – an average of 10.5 per day! Delegates will, of course, pick and choose – or snooze – their way through.

As Aurora turned into habit, it took its mandate as the voice of the industry to a higher octave by publishing the first Aurora Fact File in its November–December 2001 issue – a formidable attempt to organise, corroborate and document key data about the industry, such as ad spend and top agencies. Since then, the Fact File is published every year in Aurora’s special annual November-December issue and is the default reference and footnote to many PowerPoint presentations in boardrooms across Pakistan.

These photos of pressure-sensitive film show the pressure distribution across the bearing surface of a hex flange nut (top) and hex flange cap screws from two different suppliers (middle and bottom). This study was undertaken when the hex flange screw used in Figure 3 unexpectedly showed pressure concentrated at the edge of the clearance hole rather than outside diameter of the flange. Photo courtesy Peak Innovations Engineering

These changes have introduced the concept of a specialised review of the media planning function and its execution – independent of the media buying companies. This means that post-campaign analysis is now evaluating whether the business objectives were met as well as the overall value the client achieved.

As for the porch roof—you could either remove it entirely or cut back the sheathing and framing enough to allow the new foam to slide into place. On small porches, as long as you use a 2x plate where the rafters meet the foam, it should be fine. Foam typically used on roofs can support 15 lb. to 25 lb. per sq. in., so bearing shouldn’t be an issue. For larger roofs, you may need to provide direct framing-to-framing contact. But even though an unconditioned roof won’t benefit from being covered in foam, it will need to be detailed so that it aesthetically matches the rest of the roof retrofit work. It needs to be furred out with something so the trim details will later match.

- Hydraulic floor jacks tend to be in the form of small trolleys with one long lever arm. The take advantage of hydraulics to lift some serious weight.

Other memorable ones include ‘Hum to jaane seedhi baat, sabun ho to 707’ for 707 detergent soap; ‘Jahan mamta, wahan Dalda’; and ‘Ab bhi tawana, jab bhi tawana,’ for Tullo.

Here is how Anwar Mooraj, in a chapter of Karachi: Megacity of our times, describes the restaurant: “Le Gourmet had the usual ingredients which made for a successful night club – good food, a well-stocked cellar, wonderful music and a congenial atmosphere. Everybody who was ‘a somebody’ wanted to be seen there. Le Gourmet, however, introduced a new element – cabaret. Besides the usual assortment of heavily rouged Can-Can girls, who threw their long legs into the air while the Italian orchestra played a selection from Orpheus in the Underworld, there were also sophisticated magic shows, experiments in levitation and solo performances by a sensational local classical dancer called Panna.”

Take “quality” screw driver which isn’t quite long enough. Find steel pipe/tube with ID which is a near friction fit of the driver shaft OD. Need angle grinder & welder. Hopefully you see where I’m going with this.

I am full blown tool junkie. I admit it. When Jason requested something about tools my day was complete. When I go to the hardware store, employees smile and hand me things. Things like a 30 dollar “military grade” flashlight. Not sure what a military grade flashlight does, but sometimes curiosity wins and the bank account loses. I could write 1,500 pages on this subject but I promised not to. So, in the spirit of sticking to my assignment, here are five items that make life in the tiny garage so much easier.

OKW can customize EVOTEC on request. Services include: custom colors, RFI/EMI shielding; CNC machining; lacquering; water transfer, tampo or digital printing of logos and legends; installation and assembly of accessories; display windows; plastic and aluminum panels.