Jonathan Gold, Pulitzer Prize-winning restaurant critic, dead at 57 | Flat Torx Self Drilling Screw

This work stands as a contrast to most of the advertising that shies away from embracing our culture. When I worked in advertising in Pakistan, creative concepts were written and presented in English and then translated into Urdu for execution. Urdu copywriters were a rare breed and often not at the top of the food chain.

In 2011, the Jinnah Campaign highlighted Mr Jinnah’s views on women (the campaign kicked off on 100th International Women’s Day), minorities, the duties of a democratic government and the importance of education. The campaign’s theme was: ‘Mr Jinnah’s bequest is Pakistan’s leading media conglomerate – The Dawn Media Group’. The campaign won the Pakistan Advertisers Society (PAS) Award in the Best In Media category in 2012.

The CL5 5-axis workholding system consists of a subplate, riser, and top tooling made from a vise or a fixture plate. The subplate transforms a T-slot table into a modular fixturing plate, allowing flexible and easy clamping and locating of other tooling and/or fixtures. Every plate has built-in clamping and locating for risers, allowing for quick and accurate setups. The Quintus quick-change riser allows 5-side part access to remove a part from the machine table. The system combines the riser, quick-change capability, and precise location in one piece. Several versions of fixture plates, vises, and jaws are available.

While Yusuf concurs that greater flexibility is needed if agencies want to retain valuable, talented and dedicated female employees after they start a family, she points out that it is not financially feasible for advertising agencies to mirror the benefits offered by multinationals.

HAVE YOU BEEN KEEPING A SCORECARD, BECAUSE WE HAVEN’T. HOWEVER, WE WILL GET RIGHT ON THAT. Here is a quick synopsis, with a few added factors yet to be discussed. KTM wins the power, brake and clutch category, while Husqvarna takes the handling and wheel crowns. Every other category is a tie, as you would expect from bikes that are identical. But, perhaps there are tiebreakers yet to be discussed. Here are a few added features.

We did a remake of the TVC in the 2000s, which showed the girl as a grown up, but it didn’t do well, because times had changed and so had the target market. Earlier, a father was the sole breadwinner; today, almost everyone in the family earns.

The Engineering Exchange is a global educational networking community for engineers.Connect, share, and learn today »

The Congress theme stressed context rather than only a profession’s narcissistic interests: ‘Advertising and National Development: Challenge and Response’.

The most common thread profile is the simple V thread, with opposing faces of the thread forming an angle of 60°. This thread angle is a compromise that balances the efficiency, wear rate, strength, and most importantly, the friction of the threads. Along with the pitch, or number of threads per unit length, thread friction contributes to the self-locking, or “non-overhauling” property of most screw threads. Self-locking threads easily convert a rotational force to an axial force, but not the other way around. It’s easy to see this property in action — a nut spins easily on a screw with finger pressure, but push the nut as hard as you can along the long axis of the screw and the screw will not start spinning. Self-locking keeps tools like screw jacks from unwinding under load.

Vises are an essential piece of kit for many tasks like cutting length of pipe, bending or shaping things or generally holding something tight in place. They come in either stationary or swiveling varieties but for heavy-duty work, you really want a forged-steel one.

When General Ziaul Haq exercised total control over the media, initially through direct censorship and later by imposing self-censorship, little did he know how rapidly state control would become ineffective and the media scenario would change a few years after his death.

To see if it’s a "wood screw", a "machine screw", or a "sheet metal screw", you’d have to see the threads and especially the tip. Wood screws have broadly gapped threads, and a sharp tip, and generally a bit of a taper along their length to the point, designed to gouge themselves into the wood as you screw in but without splitting the wood. Sheet metal screws have closer spaced threads, a sharp tip, and much less taper or none: they’re used to screw into soft metal like aluminum and gouge their way in, but you generally have to pre-drill a hole for them. Machine screws have closely spaced threads, no taper, no sharp tip, and require the hole to be pre-threaded to work.