Know the Proper Tools for Metal Panel Installation | Hex Washer Head Screw

So, how to intelligently and seamlessly weave a brand into your story, getting the best for both, yet not grabbing the attention of savvy consumers in a way that interrupts the narrative? We must remember that when a brand’s consumer becomes part of an audience for a film, their receptiveness to branded content decreases; the thought of brands interrupting the sacred space of film has long been eyed with disdain by filmmakers and audiences.

The Trektop NX Glide convertible soft top has no zippers—no zippers at all. Instead, innovative plastic channels and plastic tubes with tapered ends mate to attach side and rear windows to the top. Like zippers, these gliding channels and tubes allow windows and panels to be easily removed as you desire. The beauty of this top is that these channels don’t suffer the same weaknesses as zippers and should last well into the next soft-top era.

(3) Radiator guards. Husqvarna has redesigned the radiator guards to reduce the amount of trapped dirt on the bottom of the guard. The 2018 guards have holes in them to let dirt out. You can upgrade your 2017 radiator guards with a drill.

New Way Trucks congratulates Ginove, Inc., the Canadian based refuse truck manufacturer, on producing their 150th ROTO PAC automated side-loading waste and recycling truck. ROTO PAC is Ginove’s best selling waste collection body. 

The metal front wheel is made of cheap stamped steel so you will need to drill through both sides of it. Put the BCD 130 chainring over the wheelbarrow wheel and line it up perfectly before you mark the holes to drill. Before you start drilling use a punch so the drill does not wander. I started with a small drill bit and then went bigger and bigger. The holes on the non-drive side will want to be the exact size of the bolts you are using. The holes on the drive side will need to be much bigger so the pipe you use as a standoff will fit through. The standoffs can be cut from any steel pipe that should be only slightly larger than the bolt diameters. I used a conduit pipe cutter which worked well for cutting 5 lengths of pipe to the exact same length. It’s critical that the standoff pipes go all the way through if they just rest on the top piece of sheet steel on the drive side of the wheel then when you tighten them down the two pieces of steel on either side of the hub will crush together and the wheel will not line up properly. If the standoff goes through one side of the steel wheel and rests on the non-drive side of the hub then there is nothing to crush and you can tighten down the bolts with impunity. I used bolts that were about the same size as the BCD 130 holes in my steel chainring.

With new options coming on stream, the need for specialised planning and execution agencies arose and the concept of outdoor media agencies (OMA) started taking hold – pioneered by Unilever with the appointment of Adservice, and Nestlé with the appointment of Adkings.

In 1992, PTV launched PTV 2, their first satellite channel (renamed PTV World in 1998). By the end of the decade, the penetration of foreign satellite channels had increased significantly as even low-income neighbourhoods gained access to them via cable. However, although PTV’s viewership was impacted to an extent, the advertising revenue, for the most part, was not.

Andrew Markel is the editor for Brake & Front End Magazine and has been on the staff at Babcox Media for 13 years. He is a former technician, service writer and service manager with experience at independent shops and dealerships. Andrew is also an ASE certified automotive technician. Andrew has spoken at industry events such as the SAE Brake Colloquium and FMSI Annual Conference. He has also been quoted in publications like Smart Money and Crain’s Business. He is active in motorsports and owns several vintage vehicles.

Trucks used for transport of goods developed stencils for the three main companies. New Muluk (New Country), Sitara-e-Hilal (Crescent and Star) and Taj Mahal. Some tentative painted decoration crept in when Haji Hussain, a palace decorator from Kutch Bujh settled in Karachi. In the economic boom of the sixties, the fortunes of transporters grew as industries in Karachi needed raw materials from all over Pakistan.

Yea, those are some pretty outlandish conclusions to jump to based simply on the shape of 3 screw heads and a white speck in a blurry low-res photo.

Talat Hussain was a popular voice-over artist. Others included Pervaiz Basheer and Hasan Shaheed Mirza. As far as composers were concerned, there was Sabir Saheb and Anjum Effendi, who composed the Peek Freans jingle with Alamgir.

The material displaced by the rolling process will be displaced onto the nearby thread until the minor diameter is below the blank diameter. This displaced material, above the blank diameter, produces the major diameter.