Lasers etch dirt-busting ‘lotus effect’ on aircraft | Flat Torx Self Drilling Screw

The Star invasion began in the early 2000s, bringing with it the popular saas bahu dramas into Pakistani homes, followed by a plethora of local satellite channels after the opening up of the media by President Musharraf; their advent signalled the beginning of the end of PTV’s market leadership.

This was further supported in 2003, with the publication of the first Aurora Purple Book – an agency directory that also contained statistics and key data from the Aurora Fact File. Ten years later, in 2013, with the digital economy in full swing, The Digi Handbook was launched as the online heart of the Aurora Purple Book series to give agency professionals a singular compendium that works as a reference, a toolkit and a yardstick.

In recent years, Rosebrook returned to writing fiction, as well as journalism, with contributions to Arizona Highways and True West.

They were fully functional, but they lacked aesthetics and did not even attempt to make the user experience easy. The flaw was that technology people are very good with coding but useless at design and communication.

Advertising agencies and their clients need to believe in the power of music to create recall for their products. One of the problems is that people are not coming up with solid melodic structures anymore; they are not chosen because of their talent; instead, they are chosen because they are referred by other people.

Yes I have. Drywall nail pops are the bane of many homeowners and it depends upon when and how the house was built. Nail-pops have many causes but only two results. Either the nail moves and the drywall stays put and the nail "pops" creating the tell-tale dimple or the drywall moves and the nail stays put with similar results. If you do not understand which of the two is happening, you will not take the appropriate repair steps in paint preparation and you will have doomed your efforts — the nail will pop again.

For their part, advertising agencies, which in times past infused a new activism and cohesion through their own representative body known as the Pakistan Advertising Association (PAA) declined into fractious internal strife, to be replaced briefly by the Advertising Agencies Association of Pakistan, until descending into dormancy.

On the other hand, KTM was either braver or stupider, but they stuck with bad WP coil-spring forks. The WP-built 4CS fork was just a place-saver at KTM. KTM was willing to suffer the slings and arrows of critics while waiting for the AER air fork to come online. It took a year longer than they hoped, but when it came out, it reinvigorated the air fork’s reputation. The AER fork proved that an air fork could be 3 pounds lighter, uncomplicated to live with and excellent for a wide range of riders.

Sponsored Content is a special paid section where industry companies provide high quality, objective, non-commercial content around topics of interest to the ASSEMBLY audience. All Sponsored Content is supplied by the advertising company. Interested in participating in our Sponsored Content section? Contact your local rep.

The most common design challenge on the threaded end of a bolted joint is determining the required thread engagement when using tapped holes. As with nuts, the objective is to ensure that the failure mode in the event of overtightening is by bolt fracture rather than thread strip. This mode is preferable, because it is more obvious (stripped threads don’t generate a loose bolt) and repair is generally less expensive and more dependable.

Azar’s announcement, which was in English and followed by an Urdu translation by Mustafa Ali Hamadani, was important for two reasons. One, it made radio the first medium to announce the creation of Pakistan; two, the Lahore station, which a mere hour ago was part of AIR, was officially part of the Pakistan Broadcasting Service (PBS), which subsequently became known as Radio Pakistan.

Believe it or not, I’ve been designing my plastic parts to include the bolt holes/threading for standard bolts. I’ve taken into account the standard shrinkage depending upon the print orientation and have this down to a science now. For example, using an M4 reference model shrinks down nicely in the Z-orientation to an M3. An 8-32 reference model in the Z-orientation corresponds with a 6-32 bolt in real life. X- or Y-oriented bolts at least on my printer render true so there’s no need to adjust for them.