Twitter adds Bookmarks so you can save tweets for later without liking them | Hex Washer Head Screw

These were the four most commonly cited grievances of having the government as a client. This begs the question that if working with the government is such a thankless endeavour, then why not limit agency business to the private sector? The response was refreshingly honest and unanimous, and best summed up by Sohail Kisat, Group Chairman, MCOM: “Government is the only client that allows the agency to retain a 15% commission on media placement and that is where the real money is. In the private sector, the margins are as low as two to three percent, which is why we see agencies pitching for the so-called ‘dreadful government campaigns.”’

Another difference between standard automatic screwdrivers and equipment for friction-drilling screws lies with how the fasteners are fed. Despite their relative bulk, friction-drilling screws require gentler handling than ordinary screws. That’s because the tip, which initiates the friction, is critical for the application. Dumping the screws into a vibratory feeder is not an option.

Slotted, also called flathead, drive types are a simple slotted groove across the entire head of the screw.

Sponsored Content is a special paid section where industry companies provide high quality, objective, non-commercial content around topics of interest to the ASSEMBLY audience. All Sponsored Content is supplied by the advertising company. Interested in participating in our Sponsored Content section? Contact your local rep.

If you want to make sure something is perfectly level, or vertical for that matter, you’ll want to get yourself a decent spirit level. Although there are a plethora of smartphone apps out there, you might not want to get our phone dirty or risk damaging it.

The U.S. Food and Drug Administration (FDA) and the International Standards Organization (ISO) have specific requirements for calibrating medical devices. “Medical Device Calibration: A Step-by-Step Guide to Meeting FDA and ISO Standards,” covers each aspect of calibration requirements – showing where the FDA and ISO differ and where they match – explaining how to combine them for full compliance.

3. Insert the sensor through the wheel, keeping pressure against the rear of the metal valve stem. The potted side of the sensor is to be positioned toward the wheel. Mounting the sensor upside-down can cause relearn and transmission problems. The two grommets seal the sensor and nut to the wheel.

Unless you have a standing-seam metal roof, the mounting system will use bolts similar to this. To prevent water damage, the bolt fixture will be surrounded by flashing, which is a special metal or plastic shield that slips under the surrounding roofing tiles to prevent water from getting in. The flashing will be sealed with tar or underlayment, and the bolt hole will be filled with long-life sealant, as well.

PL Robertsonhttps://en.wikipedia.org/wiki/P._L._Robertson A this screw Head is Light years better than Philips

Hex-head screws are typically small and commonly found in doorknobs, towel bars, faucet handles, even some mechanical installations and require a hex key screwdriver (also called an Allen screwdriver) to tighten or loosen. Screwdrivers and bits range in size to fit hex-head screw recesses from around 0.03” to 3/8”. Allen-type screwdrivers, or wrenches, are often L- or T-shaped manual screwdrivers, although Allen bits are available for both ratcheting screwdrivers and drills.

It was Elphinstone Street (now Zaibunissa Street) and referred to affectionately as ‘Elphi’, which was considered to be the ‘centre of the universe’ even before Partition. In addition to shops such as Ghulam Mohammad & Sons, which specialised in men’s clothing and Bliss & Co, the chemists, there were several stores selling imported goods.

We will soon be purchasing a house that has a great southern exposure and will require a new roof. You mentioned that a solar company can come in while the roof is being done to install the mounts before the roofing installation is complete but I’m wondering if there is any advantage to doing that. Does it make for a cheaper solar install or simply make it more secure b/c the installer doesn’t have to search for the studs? Are roofing companies really cool w/ stopping their work while another team goes up (if time is money)?